Grizzly G0477 Manual do Utilizador

MODEL G047715" PLANER/MOULDEROWNER'S MANUALCOPYRIGHT © APRIL, 2006 BY GRIZZLY INDUSTRIAL, INC.WARNING: NO PORTION OF THIS MANUAL MAY BE REPR

-8-Model G0477 15" Planer/MoulderAdditional Safety for Planer/MouldersNo list of safety guidelines can be complete. Every shop environment is dif

Model G0477 15" Planer/Moulder-9-Figure 2. Typical type 5-15 plug and receptacle.Serious personal injury could occur if you connect the m

-10-Model G0477 15" Planer/MoulderWear safety glasses dur-ing the entire set up pro-cess!This machine presents serious injury hazards to untr

Model G0477 15" Planer/Moulder-11-InventoryAfter all the parts have been removed from the two boxes, you should have the following items:

-12-Model G0477 15" Planer/MoulderFloor LoadRefer to the Machine Data Sheet for the weight and footprint specifications of your machine. Som

Model G0477 15" Planer/Moulder-13-Stand AssemblyThe stand for the Model G0477 must be assem-bled before the planer/moulder can be mounted on i

-14-Model G0477 15" Planer/MoulderMounting Planer/Moulder on StandComponents and Hardware Needed:Hex Bolts M8-1.25 x 80 ...

Model G0477 15" Planer/Moulder-15-Test RunOnce the assembly is complete, test run your machine to make sure it runs properly. If, during

-16-Model G0477 15" Planer/MoulderDamage to your eyes, lungs, and ears could result from using this machine without proper protective gear

Model G0477 15" Planer/Moulder-17- Note: If the cut is too heavy and bogs down the planer/moulder, turn the planer/moulder OFF immediately,



-18-Model G0477 15" Planer/MoulderHeadstock Height AdjustmentThe headstock height can be adjusted via the manual crank handle (used for fi

Model G0477 15" Planer/Moulder-19-3. Place the workpiece below the depth-of-cut gauge, as shown in Figure 15.4. Lower the headstock until

-20-Model G0477 15" Planer/MoulderMoulding KnivesTools Needed: QtyWrench 8mm ...1The G0477 h

Model G0477 15" Planer/Moulder-21-Setting Up Moulding Guide FenceComponents and Hardware Needed: QtyWing Bolts 1⁄4-20 x 11⁄4" ...

-22-Model G0477 15" Planer/MoulderFigure 22. Guide Fence Plan (shown at approx. 30% size).

Model G0477 15" Planer/Moulder-23-G4520–G4564 Moulding KnivesSelect from this terrific assortment of casing, baseboard, crown moulding a

-24-Model G0477 15" Planer/MoulderAlways disconnect power to the machine before performing maintenance. Failure to do this may result in s

Model G0477 15" Planer/Moulder-25-Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you nee

-26-Model G0477 15" Planer/MoulderPlaner/Moulder OperationsSymptom Possible Cause Possible SolutionExcessive snipe (gouge in the end of the

Model G0477 15" Planer/Moulder-27-Changing Planing KnivesPlaning knives are razor sharp! Always han-dle the planing knives with the magnets

Table of ContentsINTRODUCTION ...

-28-Model G0477 15" Planer/MoulderChanging BeltsTools Needed: QtyHex Wrench 4mm ...1Hex Wrench 5mm ..

Model G0477 15" Planer/Moulder-29-NOTICEDO NOT let the chain fall off the sprock-ets—returning it to its proper location with-out changin

-30-Model G0477 15" Planer/MoulderElectrical ComponentsFigure 29. Rear of power switch and circuit breaker (switch assembly inverted).Power Switc

Model G0477 15" Planer/Moulder-31-

-32-Model G0477 15" Planer/MoulderG0477 Body Breakdown

Model G0477 15" Planer/Moulder-33-

-34-Model G0477 15" Planer/Moulder

Model G0477 15" Planer/Moulder-35-G0477 Stand Breakdown

-36-Model G0477 15" Planer/Moulder331329323332327326333330328325324Safety labels warn about machine hazards and ways to prevent injury. The owner

Model G0477 15" Planer/Moulder-37-REF PART # DESCRIPTION REF PART # DESCRIPTION1 P0477001 CAP (LEFT) 51 PR05M EXT RETAINING RING 15MM2 PSB04M CAP

-2-Model G0477 15" Planer/MoulderIf you have any comments regarding this manual, please write to us at the address below:Grizzly Industrial, Inc.

-38-Model G0477 15" Planer/MoulderREF PART # DESCRIPTION REF PART # DESCRIPTION101 P0477101 PLUG 151 P0477151 STEP ROD102 PSB26M CAP SCREW M6-1 X

Model G0477 15" Planer/Moulder-39-REF PART # DESCRIPTION REF PART # DESCRIPTION201 P0477201 SPROCKET 251 P0477251 BEARING RETAINER202 P0477202 CH

-40-Model G0477 15" Planer/MoulderREF PART # DESCRIPTION REF PART # DESCRIPTION301 P0477301 MOTOR 2-1/2HP, 110V 316 PFN01M FLANGE NUT M8-1.25301-

Model G0477 15" Planer/Moulder-41-Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

 





Model G0477 15" Planer/Moulder-3-

-4-Model G0477 15" Planer/Moulder  

Model G0477 15" Planer/Moulder-5-Figure 1. G0477 Component and Control Identification.A. Infeed/Outfeed Roller Height AdjusterB. ON/OFF SwitchC

-6-Model G0477 15" Planer/Moulder4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing

Model G0477 15" Planer/Moulder-7-7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation i