Grizzly G0624 Manual do Utilizador

MODEL G062410" BENCHTOP LATHEOWNER'S MANUALCOPYRIGHT © NOVEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.WARNING: NO PORTION OF THIS MANUAL MAY BE R

-8-G0624 10" Benchtop LatheAdditional Safety for Wood Lathes1. KEEPING GUARDS IN PLACE. Make sure all guards are in place and that the lathe sit

G0624 10" Benchtop Lathe-9-Figure 2. Typical type 5-15 plug and receptacle.Serious personal injury could occur if you connect the machine

-10-G0624 10" Benchtop LatheWear safety glasses dur-ing the entire set up pro-cess!This machine presents serious injury hazards to untrained

G0624 10" Benchtop Lathe-11-Floor LoadRefer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some wor

-12-G0624 10" Benchtop LatheAssemblyTo install the tool rest:1. Turn the release lever on the tool rest base so it does not interfere wit

G0624 10" Benchtop Lathe-13-Damage to your eyes and lungs could result from using this machine without proper pro-tective gear. Always wear safet

-14-G0624 10" Benchtop LatheThe tailstock is equipped with a cam-action clamping system to secure it to the lathe bed. When the le

G0624 10" Benchtop Lathe-15-Installing/Removing Spur CenterThe spur center installs into the headstock spin-dle with a taper fit.To install the s

-16-G0624 10" Benchtop LatheTo remove the live center:1. Turn the quill handwheel counterclockwise until the tailstock quill bottoms ou

G0624 10" Benchtop Lathe-17-Figure 17 shows an example of a skew chisel.Figure 17. Skew chisel.• Scrapers—Mainly used where access for other



-18-G0624 10" Benchtop LatheFigure 22. Spur center properly embedded.2. Using a wood mallet, tap the point of the spur center into the ce

G0624 10" Benchtop Lathe-19-Figure 24. Typical faceplate turning operation.Faceplate turning (Figure 24) is when a workpiece is mounted to the fa

-20-G0624 10" Benchtop LatheAfter turning, the workpiece can be sanded, as shown in Figure 27, and finished (in the same manner) b

G0624 10" Benchtop Lathe-21-SECTION 5: ACCESSORIESACCESSORIESG1194—3-Jaw ChuckA "must have" for the serious wood turner. This 3

-22-G0624 10" Benchtop LatheFigure 32. Model H1064 6-PC Chisel Set.H1064—6-PC Deluxe HSS Lathe Chisel SetThis deluxe chisel set features bee

G0624 10" Benchtop Lathe-23-SECTION 6: MAINTENANCEAlways disconnect power to the machine before performing maintenance. Failure to do this

-24-G0624 10" Benchtop LatheReview the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-ops. If yo

G0624 10" Benchtop Lathe-25-SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTIONVibration noise while machine is running; noise remains constant when speed i

-26-G0624 10" Benchtop Lathe

G0624 10" Benchtop Lathe-27-G0624 Wiring Diagram

INTRODUCTION ... 2Foreword

-28-G0624 10" Benchtop LatheParts ListREF PART # DESCRIPTION REF PART # DESCRIPTION1 PSS02M SET SCREW M6-1 X 6 48 P0624048 SHAFT2 P0624002 HEADST

G0624 10" Benchtop Lathe-29-Warning Labels Parts ListSafety labels warn about machine hazards and ways to prevent injury. The owner of this machi

-30-G0624 10" Benchtop LatheGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the da

 





-2-G0624 10" Benchtop LatheINTRODUCTIONForewordWe are proud to offer the Model G0624 10" Benchtop Lathe. This machine is part of a g

G0624 10" Benchtop Lathe-3-

-4-G0624 10" Benchtop Lathe 

G0624 10" Benchtop Lathe-5-Figure 1. Model G0624 identification.A. Belt Tension Lock KnobB. Belt Cover Lock HandleC. Belt CoverD. HeadstockE.

-6-G0624 10" Benchtop LatheSafety Instructions for Machinery        

G0624 10" Benchtop Lathe-7-           