Grizzly G0614 Manual do Utilizador

Model G0613/G0614Swivel Mast Metal Cutting BandsawOWNER'S MANUALCOPYRIGHT © NOVEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.WARNING: NO PORTION OF THIS

-8-G0613/14 Swivel Mast Metal Cutting BandsawControl PanelA. ON/OFF Push Button Switch: When the cover is open, it allows access to the normal-o

G0613/14 Swivel Mast Metal Cutting Bandsaw-9-4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent

-10-G0613/14 Swivel Mast Metal Cutting Bandsaw7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure ope

G0613/14 Swivel Mast Metal Cutting Bandsaw-11-Additional Safety Instructions for Bandsaws8. FIRE HAZARD. Use EXTREME CAUTION if cutting magnesium. Us

-12-G0613/14 Swivel Mast Metal Cutting BandsawSECTION 2: CIRCUIT REQUIREMENTS110/220V Single-Phase (G0613)Amperage DrawThe Model G0613 features a

G0613/14 Swivel Mast Metal Cutting Bandsaw-13-Serious personal injury could occur if you connect your machine to the power source before you h

-14-G0613/14 Swivel Mast Metal Cutting BandsawThe Model G0613/14 was carefully packed when it left our warehouse. If you discover the machine is dama

G0613/14 Swivel Mast Metal Cutting Bandsaw-15-NOTICESome hardware/fasteners on the inventory list may arrive pre-installed on the machine. Check th

-16-G0613/14 Swivel Mast Metal Cutting BandsawFloor Load and Working ClearancesRefer to the Machine Data Sheet for the weight and footprint specific

G0613/14 Swivel Mast Metal Cutting Bandsaw-17-The Model G0613/14 is an extremely heavy machine. Serious per-sonal injury may occur if safe movi



-18-G0613/14 Swivel Mast Metal Cutting BandsawCutting Fluid SystemFIRE HAZARD! DO NOT cut magnesium when using oil-water solutions as a cuttin

G0613/14 Swivel Mast Metal Cutting Bandsaw-19-The adjustments listed below have been per-formed at the factory. However, because of the m

-20-G0613/14 Swivel Mast Metal Cutting BandsawDamage to your eyes, lungs, and ears could result from using this machine without proper protectiv

G0613/14 Swivel Mast Metal Cutting Bandsaw-21-WorkstopYour bandsaw has an adjustable workstop (Figure 14) that is easy to install and to use.To instal

-22-G0613/14 Swivel Mast Metal Cutting BandsawFigure 17. Vise clamping options.5. Use the chart shown in Figure 17 as a gui

G0613/14 Swivel Mast Metal Cutting Bandsaw-23-Blade SelectionThe Model G0613 uses a 3⁄4" wide x 82" long x 0.35" thick bandsaw bla

-24-G0613/14 Swivel Mast Metal Cutting Bandsaw       

G0613/14 Swivel Mast Metal Cutting Bandsaw-25-Feed rate is the speed at which the bow and the saw blade cuts through a workpiece. The feed rate

-26-G0613/14 Swivel Mast Metal Cutting BandsawThe following tips will help you safely and effec-tively operate your bandsaw and get the maxi-mu

G0613/14 Swivel Mast Metal Cutting Bandsaw-27-Figure 23. BladesSECTION 5: ACCESSORIESFigure 24. H5408 Blade Tensioning Gauge.H5408—Blade Tensioning Ga

Table of ContentsINTRODUCTION ... 2Foreword ... 2Cont

-28-G0613/14 Swivel Mast Metal Cutting BandsawFigure 28. Our most popular safety glasses.G7984—Face ShieldH1298—Dust Sealed Safety GlassesH1300—UV Blo

G0613/14 Swivel Mast Metal Cutting Bandsaw-29-Always disconnect power to the machine before performing maintenance. Failure to do this may resu

-30-G0613/14 Swivel Mast Metal Cutting BandsawReview the troubleshooting and procedures in this section to fix your machine if a problem develops. If

G0613/14 Swivel Mast Metal Cutting Bandsaw-31-SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTIONMachine is loud when cutting or bogs down in the cut.1. Excessi

-32-G0613/14 Swivel Mast Metal Cutting BandsawBlade ChangeChange the blade when it becomes dull, damaged, or when you are using materials that

G0613/14 Swivel Mast Metal Cutting Bandsaw-33-8. When the blade is around both wheels, adjust the position so the back of the blade is against

-34-G0613/14 Swivel Mast Metal Cutting BandsawThe blade guides have a basic factory adjust-ment, but due to shipping and storage we recom-mend

G0613/14 Swivel Mast Metal Cutting Bandsaw-35-11. Go to Setting Stops on Page 38 and com-plete the steps to make sure the cuts will be perpendicu

-36-G0613/14 Swivel Mast Metal Cutting BandsawTo adjust the blade guides:1. Make sure the blade is oiled, tensioned, and tracking correctly.2. DISCO

G0613/14 Swivel Mast Metal Cutting Bandsaw-37-12. When finished with the carbide guide adjust-ments, make sure the ball bearing guide (Figure

-2-G0613/14 Swivel Mast Metal Cutting BandsawIf you have any comments regarding this manual, please write to us at the address below:Grizzly Industria

-38-G0613/14 Swivel Mast Metal Cutting BandsawThe blade swivel stops are factory set. However, due to shipping and storage we recommend that you chec

G0613/14 Swivel Mast Metal Cutting Bandsaw-39-Feed StopIt may be necessary to adjust the feed stop before you make blade adjustments. The

-40-G0613/14 Swivel Mast Metal Cutting BandsawThe blade-to-vise squareness is factory set. However, due to shipping and storage we recom-mend tha

G0613/14 Swivel Mast Metal Cutting Bandsaw-41-Electrical Components (G0613)Figure 1. Pump motor wiring.Figure 59. G0613 saw motor junction box.Figure

-42-G0613/14 Swivel Mast Metal Cutting BandsawElectrical Components (G0614)Figure 65. G0614 Emergency stop button.Figure 63. G0614 Pump and speed swit

G0613/14 Swivel Mast Metal Cutting Bandsaw-43-Electrical Components (G0614)Figure 66. G0614 contactors.Figure 67. G0614 control box.

-44-G0613/14 Swivel Mast Metal Cutting BandsawElectrical Components (G0614)Figure 68. G0614 pump motor data/connection.Figure 69. G0614 pump relay.Fig

G0613/14 Swivel Mast Metal Cutting Bandsaw-45-Electrical Components (G0614)Figure 72. G0614 blade stop limit switch.Figure 71. G0614 main junction.

-46-G0613/14 Swivel Mast Metal Cutting BandsawG0613 220V Single-Phase Wiring Diagram

G0613/14 Swivel Mast Metal Cutting Bandsaw-47-G0614 220V Three-Phase Wiring Diagram

G0613/14 Swivel Mast Metal Cutting Bandsaw-3-Machine Data SheetMODEL G0613 SWIVEL MAST METAL-CUTTING BANDSAWCustomer Service #: (570) 546-9663 • To Or

-48-G0613/14 Swivel Mast Metal Cutting Bandsaw

G0613/14 Swivel Mast Metal Cutting Bandsaw-49-Parts List (G0613)REF PART # DESCRIPTION REF PART # DESCRIPTION1 PSB64M CAP SCREW M10-1.5 X 25 41 PSS06M

-50-G0613/14 Swivel Mast Metal Cutting BandsawHeadstock and Bow Breakdown (G0614)

G0613/14 Swivel Mast Metal Cutting Bandsaw-51-Parts List (G0614)REF PART # DESCRIPTION REF PART # DESCRIPTION1 PSB64M CAP SCREW M10-1.5 X 25 43 P06140

-52-G0613/14 Swivel Mast Metal Cutting Bandsaw

G0613/14 Swivel Mast Metal Cutting Bandsaw-53-Parts List (G0613)REF PART # DESCRIPTION REF PART # DESCRIPTION100 P0613100 VISE JAW ADJUSTABLE ROD 131

-54-G0613/14 Swivel Mast Metal Cutting Bandsaw

G0613/14 Swivel Mast Metal Cutting Bandsaw-55-Parts List (G0614)REF PART # DESCRIPTION REF PART # DESCRIPTION100 P0614100 VISE JAW BRACKET(REAR) 131 P

-56-G0613/14 Swivel Mast Metal Cutting BandsawElectrical Box Breakdown (G0613)Parts List (G0613)REF PA

G0613/14 Swivel Mast Metal Cutting Bandsaw-57-Electrical Box Breakdown (G0614)

-4-G0613/14 Swivel Mast Metal Cutting BandsawMain Specifications: Operation Info Blade Speeds ...

-58-G0613/14 Swivel Mast Metal Cutting BandsawParts List (G0614)REF PART # DESCRIPTION REF PART # DESCRIPTION232 PLW03M LOCK WASHER 6MM 249 P0614249 R

G0613/14 Swivel Mast Metal Cutting Bandsaw-59-Cabinet and Gearbox Breakdown (G0613 & G01614)

-60-G0613/14 Swivel Mast Metal Cutting Bandsaw Parts List (G0613)REF PART # DESCRIPTION REF PART # DESCRIPTION300 P0613300 FRONT PANEL 311 P0613311 WO

G0613/14 Swivel Mast Metal Cutting Bandsaw-61-REF PART # DESCRIPTION REF PART # DESCRIPTION300 P0613300 FRONT PANEL 311 P0613311 WORM SHAFT301 P061330

-62-G0613/14 Swivel Mast Metal Cutting BandsawGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchase

 





G0613/14 Swivel Mast Metal Cutting Bandsaw-5-Machine Data SheetMODEL G0614 SWIVEL MAST METAL-CUTTING BANDSAWCustomer Service #: (570) 546-9663 • To Or

-6-G0613/14 Swivel Mast Metal Cutting BandsawMain Specifications: Operation Info Blade Speeds .....

G0613/14 Swivel Mast Metal Cutting Bandsaw-7-Figure 1. G0613/14 Machine Identification.A. Blade Tension HandwheelB. Cutting Fluid Flow ValvesC. Con